ProClip In-Vehicle Mounting Solutions for TomTom
Username Password
Forgot Your Password?
Currently shipping to: United States
Home
Coming SoonDemo VideoNewsProduct ReviewsPhoto GalleryAbout UsContact Us
McAfee Secure sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams
Search by item No:

Extension Plates

The Extension Plates help you keep two devices next to each other on the same mount, extend your device to the left or right to avoid interference with other dashboard controls, lower or raise your device, keep it in a more upright position for better reception etc. – truly customize your mounting solution.

Picture of ProClip ProClip Extension plates - Horizontal Extension Plate. Copyright ProClip USA.

ProClip Extension plates - Horizontal Extension Plate

Item No. 215397
Keep two devices next to each other on the same mountIf you want to have two devices attached next to each other, this is what you are looking for. The Horizontal Extension Plate attaches to the ProClip Vehicle Mount or Tilt Swivel directly. It has several hole patterns e.g. for the ProClip standard (two holes in a center line) and the AMPS standard (Four holes in an almost square pattern) The Horizontal Extension Plate can hold either 1 vertical device and 1 horizontal device or 2 vertical devices next to each other. Dimensions: 155 x 50 x 5 mm / 6.10 x 1.97 x 0.19 inches.
USD $10.99
Picture of ProClip ProClip Extension plates - Left/Right Extension Plate. Copyright ProClip USA.

ProClip Extension plates - Left/Right Extension Plate

Item No. 215183
Extends approx. 38 mm / 1.5 inches.If you want to extend your device to the left or right from the Vehicle Mount for better viewing, or to avoid interference with the dashboard controls/displays, this is what you are looking for. This extension plate is only to be used with one device.
USD $10.99
Picture of ProClip ProClip Extension plates - Left/Right Extension Plate. Copyright ProClip USA.

ProClip Extension plates - Left/Right Extension Plate

Item No. 215395
Extends approx. 25 mm / 1 inch.Avoid interference with the dashboard controls/displays when using wide devices! If you want to extend your device to the left or right from the Vehicle Mount (especially the ProClip Angled Mount) to avoid interference with the dashboard controls/displays, this is what you are looking for. This extension plate is only to be used with one device.
USD $10.99
Picture of ProClip ProClip Extension plates - Vertical Extension Plate. Copyright ProClip USA.

ProClip Extension plates - Vertical Extension Plate

Item No. 213065
Position your device higher or lower on the mount! Moves device approximately 2 inches up or down. Position your device higher or lower on the mount. If you want to position your device higher or lower from the mount, this is what you are looking for. The Vertical Extension Plate attaches to the ProClip Dashboard Mount or directly to a flat surface.
USD $10.99
Picture of ProClip ProClip Extension plates - Vertical Extension Plate for two devices. Copyright ProClip USA.

ProClip Extension plates - Vertical Extension Plate for two devices

Item No. 215437
Keep two devices above each other on the same mount.If you want to have two devices attached above each other, this is what you are looking for. The Vertical Extension Plate attaches to the ProClip Vehicle Mount or Tilt Swivel directly. It has several hole patterns e.g. for the ProClip standard (two holes in a center line) and the AMPS standard (Four holes in an almost square pattern) The Vertical Extension Plate is primarily designed for use with the Garmin Nuvi Ball Mount, TomTom Active Docks, Magellan 1 and 2 Prong Mounting Plates and the Richter 4 Prong Mounting Plate, which attaches at the bottom of the plate plus one other device to be attached on top of the plate. Dimensions: 155 x 50 x 5 mm / 6.10 x 1.97 x 0.19 inches.
USD $10.99
Picture of ProClip ProClip Extension plates - Angled Extension Plate. Copyright ProClip USA.

ProClip Extension plates - Angled Extension Plate

Item No. 215228
If you want to extend your device upwards from the Vehicle Console Mount for better viewing, this is what you are looking for. This item can be used with or without a Tilt Swivel, which is not included, but can be found by clicking Tilt & Swivel Mounts on the left side of the page. Then select Tilt Swivel Mount. (Item # 215453)
USD $14.99
Picture of ProClip ProClip Extension plates - Angled Extension Plate (Thick). Copyright ProClip USA.

ProClip Extension plates - Angled Extension Plate (Thick)

Item No. 215413
If you want to extend your device upwards from the Vehicle Console Mount for better viewing, this is what you are looking for. This item can be used with or without a Tilt Swivel, which is not included, but can be found by clicking Tilt & Swivel Mounts on the left side of the page. Then select Tilt Swivel Mount. (Item number 215453)
USD $15.99
Picture of ProClip ProClip Extension plates - Block Spacer 14 mm/ 0.55 inch. Copyright ProClip USA.

ProClip Extension plates - Block Spacer 14 mm/ 0.55 inch

Item No. 215450
Extend your holder from car mount! This Block Spacer will extend your device holder/mount 14 mm/ 0.55 inch from the car mount. Screws for attaching the Block Spacer to the car mount are enclosed.
USD $12.99
Picture of ProClip ProClip Extension plates - Block Spacer 19 mm/ 0.75 inch. Copyright ProClip USA.

ProClip Extension plates - Block Spacer 19 mm/ 0.75 inch

Item No. 215451
Extend your holder from car mount! This Block Spacer will extend your device holder/mount 19 mm/ 0.75 inch from the car mount. Screws for attaching the Block Spacer to the car mount are enclosed.
USD $12.99
Picture of ProClip ProClip Tilt Swivel Mount - Small Pedestal Mount with Multi Angle Tilt Swivel. Copyright ProClip USA.

ProClip Tilt Swivel Mount - Small Pedestal Mount with Multi Angle Tilt Swivel

Item No. 215421
Angle, tilt, swivel and extend your holder/device for a better viewing position. This mount swivels 360 degrees horizontally and vertically. It extends 2.5 inches/ 62 mm and can be attached to any flat surface. The face plate has several hole patterns including AMPS to accommodate most holders, cradles, mounts and car kits. The face plate is 1.65 x 1.95 inches / 42 x 50 mm. The base plate is 1.65 x 1.95 inches / 42 x 50 mm and it has one hole in each corner. Dimensions: 2.5 x 1.65 x 1.95 inches / 62 x 42 x 50 mm.
USD $49.99